ATHENA gasket cylinder head cover
Athena gaskets are a good choice for your engine and are a top quality guarantee. Valve cover gasket Gasket to be changed on every reconditioningDelivered without screw gaskets
ATHENA valve cover gasket
ATHENA is one of the world's best-known manufacturers of cylinder-piston sets for 2- and 4-stroke engines. The high-performance components from this manufacturer improve engine performance while maintaining its reliability. Valve cover gasket set For a high-quality overhaul The gaskets must always be replaced every time the engine is overhauled Supplied without screw gaskets
Blinker front left/ rear right for: SUZUKI GS650F BANDIT '04-08
Dimensions and properties identical to standard component.
Blinker front left/ rear right for: SUZUKI SV650 '03-08, SV1000 '03-06.
Dimensions and properties identical to standard component.
Blinker, front right / rear left for: SUZUKI GS650F BANDIT '04-08
Dimensions and properties identical to standard component.
Blinker, front right / rear left for: SUZUKI SV650 '03-08, SV1000 '03-06.
Dimensions and properties identical to standard component.
Electrosport regulator ESR 550
Regulator ESR 550(technical changes to the connector and its assignment will invalidate the warranty) Block connector A 6-way, 5-way, 3 x black, 1 x green, 1 x redATTENTION: This regulator is not suitable for a lithium-ion battery! The battery or other electronic components may be damaged!Suitable for the following battery types:Lead/acid, lead/acid MF, AGM, pure lead or gel
Electrosport Stator - Suzuki GSX-R600/750/1000
ElectroSport stators are designed to be direct replacements to original equipment Manufactured to handle higher power loads Developed in the USAOne of the best value for money
Factory Links steering head bearing kit TM EN125/250/300
ContainsDust Seals x2, Tapered Roller x2Steering Stem Bearing Service Kits Full Service Steering Stem OEM quality Set OEM type tapered roller bearings NBR Race Dust Seals
Factory Links wheel bearing set
Bearing set for front wheel FACTORY LINKS bearings are packed with a heavy-duty premium marine grease and an additive of a special complex thickener that allows it to be virtually waterproof. It provides unsurpassed rust and corrosion protection. Also to keep out any moisture, we've gone from a 30% grease fill to a 60% for harsh conditions. Our FACTORY LINKS ball bearings are specifically designed for off-road use, unlike industrial 2RS ball bearings which offer low torque resistance and therefore low resistance to water ingress.
HIGHSIDER intelligent clutch switch For Suzuki / Kawasaki
HIGHSIDER smart clutch switch for various modelsIt can happen that the original contact switch on your motorcycle gives up the ghost and you need a new switch. In this case, you can get a new switch from our range. These spare parts are of OEM quality and are said to be extremely durable. The replacement is done in no time at all and your driving safety is restored. Scope of delivery: 1 piece
HIGHSIDER pro Akron grip rubber black 7/8 inch (22.2 mm), 132 mm
HIGHSIDER AKRON handlebar grip rubber, black with aluminum ring in various colors - Styling for your bike - The stylish 7/8 inch handlebar grips HIGHSIDER AKRON create a new kind of design language with the overlapping of the two aluminum sleeves. The outer one embodies timeless design with its lines and its trapezoidal tongues form a beautiful contrast to the bead-blasted black aluminum cylinder underneath. The HIGHSIDER lettering is incorporated into the handle structure. The removable end caps allow the mounting of handlebar end indicators, handlebar end mirrors or handlebar weights. The grips give your bike the elegant HIGHSIDER look and enhance its appearance. Our accessory tip: Excellent in combination with the visually coordinated design handlebar weights from our own company. The handlebar ends pick up on the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions:Suitable for 7/8 inch (22 mm) Length: 132 mm Outer diameter rubber: approx. 34 mm Outer diameter aluminum sleeve: approx. 37 mm Scope of delivery: 1 pair
HIGHSIDER pro Akron grip rubber red 7/8 inch (22.2 mm), 132 mm
HIGHSIDER AKRON handlebar grip rubber, black with aluminum ring in various colors - Styling for your bike - The stylish 7/8 inch handlebar grips HIGHSIDER AKRON create a new kind of design language with the overlapping of the two aluminum sleeves. The outer one embodies timeless design with its lines and forms a beautiful contrast with the trapezoidal tongues to the bead-blasted black aluminum cylinder underneath. The HIGHSIDER lettering is incorporated into the handle structure. The removable end caps allow the mounting of handlebar end indicators, handlebar end mirrors or handlebar weights. The grips give your bike the elegant HIGHSIDER look and enhance its appearance. Our accessory tip: Excellent in combination with the visually coordinated design handlebar weights from our own company. The handlebar ends pick up on the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions:Suitable for 7/8 inch (22 mm) Length: 132 mm Outer diameter rubber: approx. 34 mm Outer diameter aluminum sleeve: approx. 37 mm Scope of delivery: 1 pair
HIGHSIDER pro Akron Grip Rubber Titanium 7/8 inch (22.2 mm), 132 mm
HIGHSIDER AKRON handlebar grip rubber, black with aluminum ring in various colors - Styling for your bike - The stylish 7/8 inch handlebar grips HIGHSIDER AKRON create a new kind of design language with the overlapping of the two aluminum sleeves. The outer one embodies timeless design with its lines and its trapezoidal tongues form a beautiful contrast to the bead-blasted black aluminum cylinder underneath. The HIGHSIDER lettering is incorporated into the handle structure. The removable end caps allow the mounting of handlebar end indicators, handlebar end mirrors or handlebar weights. The grips give your bike the elegant HIGHSIDER look and enhance its appearance. Our accessory tip: Excellent in combination with the visually coordinated design handlebar weights from our own company. The handlebar ends pick up on the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions:Suitable for 7/8 inch (22 mm) Length: 132 mm Outer diameter rubber: approx. 34 mm Outer diameter aluminum sleeve: approx. 37 mm Scope of delivery: 1 pair
HIGHSIDER Pro Akron-Flash LED Bar End Indicator Housing Black / Lens Orange (Pair), Front
HIGHSIDER AKRON-FLASH LED handlebar end indicators, E-approved as front direction indicator - attractive handlebar end with flashing function - With these handlebar end indicators, HIGHSIDER once again demonstrates a real flair for outstanding design and top functionality. The ultra-bright, adjustable flashing angle indicator lights of the latest generation from HIGHSIDER provide unmistakable directional indication. The handlebar end indicators with tinted glass, high-quality CNC-milled aluminum housing and characteristic cap are simply beautiful. Packaged so harmoniously, the front direction indicators literally disappear from the vehicle when not in use. Easy to fit thanks to the clamping system with various sleeves. Universal fit for 7/8, 1 inch or X-Bar tubular handlebars with an inner diameter of 12 to 22 mm. The cables are routed in the handlebars and are a good length at approx. 100 cm. Look forward to the HIGHSIDER AKRON-FLASH LED handlebar end indicators, which are by no means commonplace. Make your mark - with the innovative blinker series from HIGHSIDER, you not only show where you want to go, but also who you are. This is trend-setting design at its best. Dimensions:Width: 36 mmDiameter: 34.5 mmCable length: approx. 1000 mm Angle of the light modules continuously adjustable by 26°. Connections: Power consumption: 13.5 V, 0.26 A, 3.5W Yellow cable = blinker (+) Black cable = earth (-) Scope of delivery: 1 pair 2 x clamping sleeves Ø 13 mm, Ø 16 mm3 x centering ring2 x central screw M6 with fastening ring for the HIGHSIDER AKRON-FLASH, and cone nut M6. Note: Resistors or a flasher relay may be required for correct flashing.
HIGHSIDER Pro Akron-Flash LED Bar End Indicator Housing Black-Titanium / Lens Orange (Pair), Front
HIGHSIDER AKRON-FLASH LED handlebar end indicators, E-approved as front direction indicator - attractive handlebar end with flashing function - With these handlebar end indicators, HIGHSIDER once again demonstrates a real flair for outstanding design and top functionality. The ultra-bright, adjustable flashing angle indicator lights of the latest generation from HIGHSIDER provide unmistakable directional indication. The handlebar end indicators with tinted glass, high-quality CNC-milled aluminum housing and characteristic cap are simply beautiful. Packaged so harmoniously, the front direction indicators literally disappear from the vehicle when not in use. Easy to fit thanks to the clamping system with various sleeves. Universal fit for 7/8, 1 inch or X-Bar tubular handlebars with an inner diameter of 12 to 22 mm. The cables are routed in the handlebars and are a good length at approx. 100 cm. Look forward to the HIGHSIDER AKRON-FLASH LED handlebar end indicators, which are by no means commonplace. Make your mark - with the innovative blinker series from HIGHSIDER, you not only show where you want to go, but also who you are. This is trend-setting design at its best. Dimensions:Width: 36 mmDiameter: 34.5 mmCable length: approx. 1000 mm Angle of the light modules continuously adjustable by 26°. Connections: Power consumption: 13.5 V, 0.26 A, 3.5W Yellow cable = blinker (+) Black cable = earth (-) Scope of delivery: 1 pair 2 x clamping sleeves Ø 13 mm, Ø 16 mm3 x centering ring2 x central screw M6 with fastening ring for the HIGHSIDER AKRON-FLASH, and cone nut M6. Note: Resistors or a flasher relay may be required for correct flashing.
HIGHSIDER pro Akron-LS handlebar weights
HIGHSIDER AKRON-LS handlebar weights, black with cap in various colors - Styling for your bike - With these elegantly designed handlebar ends with handlebar end mirror mount, you can design your bike in detail according to your ideas. These end pieces serve as mounts for all HIGHSIDER & SHIN YO handlebar end mirrors with external handlebar clamps. Handlebar ends also serve to reduce annoying vibrations on the handlebars. Thanks to the clamping system with various sleeves, universally suitable for 7/8 (Ø22 mm), 1 inch (Ø25.4 mm) or X-Bar (Ø28.6 mm) tubular handlebars with an inner diameter of 12 to 22 mm. Our accessory tip: Excellent in combination with the visually coordinated AKRON designer handlebar grips from our own company. The caps of the handlebar ends mirror the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. If you do want to switch back to handlebar mirrors, you can use the optionally available color rings instead of a handlebar end mirror in just a few simple steps and thus set additional color accents. The color rings are simply slid over the handlebar end and fastened with the grub screw on the ring. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Handlebar weight Ø: 37.4 mm Width: 29 mm Mounting for mirror: Ø 29.90 mm, width: 12 mm Scope of delivery: 1 pair incl. 2 clamping sleeves each with D. 12 mm and D. 16 mm 2 spacer sleeves each with D. 14 mm, D. 18 mm and D. 21 mm 2 x M6 central bolts 2 x M6 conical nuts NOTE: For handlebar ends with clamping system, the ends of the handlebars must not be blocked by threaded inserts or similar. Handlebar ends do not have to be approved and therefore do not require any test marks, certificates or ABEs.
HIGHSIDER pro Akron-LS handlebar weights red (pair)
HIGHSIDER AKRON-LS handlebar weights, black with cap in various colors - Styling for your bike - With these elegantly designed handlebar ends with handlebar end mirror mount, you can design your bike in detail according to your ideas. These end pieces serve as mounts for all HIGHSIDER & SHIN YO handlebar end mirrors with external handlebar clamps. Handlebar ends also serve to reduce annoying vibrations on the handlebars. Thanks to the clamping system with various sleeves, universally suitable for 7/8 (Ø22 mm), 1 inch (Ø25.4 mm) or X-Bar (Ø28.6 mm) tubular handlebars with an inner diameter of 12 to 22 mm. Our accessory tip: Excellent in combination with the visually coordinated AKRON designer handlebar grips from our own company. The caps of the handlebar ends mirror the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. If you do want to switch back to handlebar mirrors, you can use the optionally available color rings instead of a handlebar end mirror in just a few simple steps and thus set additional color accents. The color rings are simply slid over the handlebar end and fastened with the grub screw on the ring. Precisely coordinated - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Handlebar weight Ø: 37.4 mm Width: 29 mm Mounting for mirror: Ø 29.90 mm, width: 12 mm Scope of delivery: 1 pair incl. 2 clamping sleeves each with D. 12 mm and D. 16 mm 2 spacer sleeves each with D. 14 mm, D. 18 mm and D. 21 mm 2 x M6 central bolts 2 x M6 conical nuts NOTE: For handlebar ends with clamping system, the ends of the handlebars must not be blocked by threaded inserts or similar. Handlebar ends do not have to be approved and therefore do not require any test marks, certificates or ABEs.
HIGHSIDER pro Akron-LS handlebar weights silver (pair)
HIGHSIDER AKRON-LS handlebar weights, black with cap in various colors - Styling for your bike - With these elegantly designed handlebar ends with handlebar end mirror mount, you can design your bike in detail according to your ideas. These end pieces serve as mounts for all HIGHSIDER & SHIN YO handlebar end mirrors with external handlebar clamps. Handlebar ends also serve to reduce annoying vibrations on the handlebars. Thanks to the clamping system with various sleeves, universally suitable for 7/8 (Ø22 mm), 1 inch (Ø25.4 mm) or X-Bar (Ø28.6 mm) tubular handlebars with an inner diameter of 12 to 22 mm. Our accessory tip: Excellent in combination with the visually coordinated AKRON designer handlebar grips from our own company. The caps of the handlebar ends mirror the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. If you do want to switch back to handlebar mirrors, you can use the optionally available color rings instead of a handlebar end mirror in just a few simple steps and thus set additional color accents. The color rings are simply slid over the handlebar end and fastened with the grub screw on the ring. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Handlebar weight Ø: 37.4 mm Width: 29 mm Mounting for mirror: Ø 29.90 mm, width: 12 mm Scope of delivery: 1 pair incl. 2 clamping sleeves each with D. 12 mm and D. 16 mm 2 spacer sleeves each with D. 14 mm, D. 18 mm and D. 21 mm 2 x M6 central bolts 2 x M6 conical nuts NOTE: For handlebar ends with clamping system, the ends of the handlebars must not be blocked by threaded inserts or similar. Handlebar ends do not have to be approved and therefore do not require any test marks, certificates or ABEs.
