The HIGHSIDER license plate holder AKRON-RS adapts perfectly to the lines of your bike through its design.The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.The license plate is made of sheet steel and 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating.This ensures an optimal fit and durability.The stepless adjustment allows you to bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.The turn signal holders of the AKRON-RS are adjustable in width and thus suitable for any type of accessory turn signals. This adjustability allows you to adjust the position for your turn signals to the most different license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side.You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem.To screw the license plate securely and reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside.Details:- model-specific mount- infinitely adjustable turn signal holder- slotted turn signal mount for easy installation without cable separation- infinitely adjustable reflector, E-approved- suitable for European license plates- infinitely adjustable angle of inclination- additional screw for optimal position security- easy fixation without further work steps (e.g. drilling)- easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes- Model-related holder with mounting parts- AKRON-RS license plate holder- Adjustable turn signal brackets- E-tested reflector with adjustable holder- Mounting instructionsNotes:- A special turn signal holder is optionally available for the original turn signals in the accessories tab.- If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones.Tips:If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Discreet and straightforward: The PRO Micro fits on almost any tank and safely transports small necessities such as vehicle documents and valuables. Like all PRO tank bags, the Micro sits on an EVA plastic base that guarantees high dimensional stability. The volume of the tank bag can be expanded with the help of a zipper. The PRO tank bags offer elegant and timeless design combined with durable materials and well thought-out product features: Ballistic nylon protects the luggage from shocks, wind and weather. The top made of laminated EVA material gives the bags a distinctive shape and, in conjunction with a MOLLE attachment, ensures a secure hold for smartphone and tablet holders.The guide rail of the top ring, which is already attached at the factory, allows a much simplified adjustment of the tank bag to the shape of the tank and the ergonomic needs of the rider. Only the PRO tank bags offer this flexibility. To match, SW-MOTECH offers the patented PRO tank rings made of fiberglass-reinforced plastic. They are manufactured to match the motorcycle model. (You can find these in the vehicle category and under the article under accessories)The robust PRO tank ring with magnetic guide aid secures the PRO tank bags with a mechanical QUICK-LOCK snap-in lock. This allows the tank bags to be attached or removed with just one movement. Volume expansion by zipper from 3 to 5 liters The patented PRO tank ring gives PRO tank bags a secure hold Magnetic guide in PRO tank ring for easy attachment Pre-mounted guide rail of the top ring for ergonomic adjustment of the tank bag Top and bottom of tank bag made of laminated and dimensionally stable EVA plastic Made of robust and especially UV-resistant 1680D Ballistic Nylon with water-repellent inner coating MOLLE attachment made of sturdy Hypalon material on the top for smartphone and tablet holder Reflective details for better visibility Mesh pockets inside Weather protection with included rain cover Robust carrying handle Cable grommet on the front and back side Can be used with cable lock or anti-theft device Scope of delivery 1 x PRO Micro tank bag 1 x PRO top ring 1 x PRO Micro rain cover Mounting instructions Mounting material Details Material: 1680D Ballistic Nylon Color: black / gray Dimensions: 27,0 x 20,5 x 11,0 cm Total weight: 0 ,8 kg Total volume: 3 ,0-5,0 l Note For mounting on the tank, the matching PRO tank ring is required. (You can find this in the vehicle category and under the article under accessories) The tank bags of the PRO series can not be combined with the EVO tank rings.
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Discreet and straightforward: The PRO Micro fits on almost any tank and safely transports small necessities such as vehicle documents and valuables. Like all PRO tank bags, the Micro sits on an EVA plastic base that guarantees high dimensional stability. The volume of the tank bag can be expanded with the help of a zipper. The PRO tank bags offer elegant and timeless design combined with durable materials and well thought-out product features: Ballistic nylon protects the luggage from shocks, wind and weather. The top made of laminated EVA material gives the bags a distinctive shape and, in conjunction with a MOLLE attachment, ensures a secure hold for smartphone and tablet holders.The guide rail of the top ring, which is already attached at the factory, allows a much simplified adjustment of the tank bag to the shape of the tank and the ergonomic needs of the rider. Only the PRO tank bags offer this flexibility. To match, SW-MOTECH offers the patented PRO tank rings made of fiberglass-reinforced plastic. They are manufactured to match the motorcycle model. (You can find these in the vehicle category and under the article under accessories)The robust PRO tank ring with magnetic guide aid secures the PRO tank bags with a mechanical QUICK-LOCK snap-in lock. This allows the tank bags to be attached or removed with just one movement. Volume expansion by zipper from 3 to 5 liters The patented PRO tank ring gives PRO tank bags a secure hold Magnetic guide in PRO tank ring for easy attachment Pre-mounted guide rail of the top ring for ergonomic adjustment of the tank bag Top and bottom of tank bag made of laminated and dimensionally stable EVA plastic Made of robust and especially UV-resistant 1680D Ballistic Nylon with water-repellent inner coating MOLLE attachment made of sturdy Hypalon material on the top for smartphone and tablet holder Reflective details for better visibility Mesh pockets inside Weather protection with included rain cover Robust carrying handle Cable grommet on the front and back side Can be used with cable lock or anti-theft device Scope of delivery 1 x PRO Micro tank bag 1 x PRO top ring 1 x PRO Micro rain cover Mounting instructions Mounting material Details Material: 1680D Ballistic Nylon Color: black / gray Dimensions: 27,0 x 20,5 x 11,0 cm Total weight: 0 ,8 kg Total volume: 3 ,0-5,0 l Note For mounting on the tank, the matching PRO tank ring is required. (You can find this in the vehicle category and under the article under accessories) The tank bags of the PRO series can not be combined with the EVO tank rings.
"120" Original Yamaha Heated Grips
Heated grips as a replacement for the standard grips. Details: Fully integrated Warm hands even on cold days Equipped with a temperature control switch—three temperature settings available Optional programming of settings for each motorcycle or scooter Automatic shut-off function conserves battery power Includes control switch Handle length is 120 mm Compatible with the following models: XSR 900 GP (26-) X-MAX 300 (25-) N-MAX 125 (25-)
Pillion seat "Comfort" for Yamaha Ténéré 700 (19-24)
For those who travel in pairs, the Isotta comfort pillion seat for the Yamaha Ténéré 700 (2019-2024 models) was developed to offer the passenger maximum comfort - without compromising the look of the motorcycle or off-road performance. This seat features a higher profile compared to the original seat, which allows for a more natural, relaxed and stable seating position even on long rides. Thanks to the 100% Italian design, it blends seamlessly into the lines of the motorcycle and maintains a dynamic, sleek appearance - ideal for road and off-road use. Like all Isotta seats, this one is supplied as a complete unit in a plug & play version that can be fitted immediately without any modifications: simply replace the original seat and immediately enjoy a better riding experience. Made from high-quality, fully waterproof and wear-resistant materials, this seat is suitable for all weather conditions. Colors: Blue: black base with blue accents Red: black base with white and red details Black: all black design with gray accents
"Double seat" Black with white piping for Vespa GTS
Double seat for Vespa GTS in black leatherette with white piping. Fits from year of manufacture 2008 - 2013
12 V socket for Honda CRF1100L Africa Twin original 2020-
This 12 V socket, installed on the instrument panel of the cockpit, is ideal for powering or charging electrical devices.
12 V socket Versys650 2014 Original Kawasaki
This kit works only with relay kit 99994-0195.
