ADAPTER TYPE 2 FOR TANK BAG QUICK FASTENING
Tank ring to enable the fitting of Oxford QR quick release bags to your motorcycle tank. Made from 304 grade stainless steel deburred and shot basted to give a professional high quality feel. Please see attached fitting list to select your Type - Type 1 to 6 available
BMC sports air filter for Triumph Street Triple 765 (18-)
The BMC standard air filters are made from the best materials and guarantee a much higher air flow rate than conventional paper filters. The comprehensive know-how from racing is used in the production of the performance-optimized filters and each one meets the highest requirements. For example, the frame of the filters cannot break, the filtering, reusable cotton fabric is impregnated with a special oil and the aluminum mesh is resistant to gasoline vapors and oxidation thanks to treatment with an epoxy solution. Why choose BMC? Better than OEM filters Better than synthetic filters Better than other cotton filters Highest quality Rigorous testing procedures Ecological and economical Winner in all categories BMC is active in numerous sectors: Automotive, racing, aviation, marine and industrial, always in accordance with the specific regulations and requirements of each of these sectors. Accordingly, BMC tests extremely rigorously and accurately to ensure that its air filters are of the highest possible quality. The technical solutions applied by BMC are derived from the results of continuous and intensive laboratory testing. BMC carries out filtration tests in accordance with the international standards for air filters (ISO 5011). BMC air filters have a filtration efficiency of 98.5 percent.BMC's filter frame construction is manufactured in a unique process called "full molding". This allows the striking red filter to be produced in a single molding process without the need to glue the corners, which would cause breakage. Of all the filters available on the market, the BMC air filter has the least overhanging rubber material (less than 6 mm), thus maximizing the filter surface area.Take a look at our YouVideo:
Factory Links steering head bearing kit TM EN125/250/300
ContainsDust Seals x2, Tapered Roller x2Steering Stem Bearing Service Kits Full Service Steering Stem OEM quality Set OEM type tapered roller bearings NBR Race Dust Seals
Factory Links wheel bearing set
Bearing set for front wheel FACTORY LINKS bearings are packed with a heavy-duty premium marine grease and an additive of a special complex thickener that allows it to be virtually waterproof. It provides unsurpassed rust and corrosion protection. Also to keep out any moisture, we've gone from a 30% grease fill to a 60% for harsh conditions. Our FACTORY LINKS ball bearings are specifically designed for off-road use, unlike industrial 2RS ball bearings which offer low torque resistance and therefore low resistance to water ingress.
HIGHSIDER pro blinker adapter black original, for license plate holder, Aprilia/BMW/Triumph/Yamaha (Pa
Original blinker adapter Suitable for various APRILIA/BMW/TRIUMPH/YAMAHA R125 models. With this black aluminum turn signal adapter, the original turn signals can be used on our HIGHSIDER or HIGHSIDER pro license plate holders. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Scope of delivery: 1 pair
HIGHSIDER pro blinker adapter For original indicators, For license plate holder, For Triumph
With this black aluminum blinker adapter, the original indicators can be used on our HIGHSIDER or HIGHSIDER pro license plate holders. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Scope of delivery: 1 pair
HIGHSIDER pro license plate holder Akron-RS Without lighting
HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design.The model-specific holder of the HIGHSIDER AKRON-RS enables mounting on the original mounting points of your bike and thus replacement without further drilling or cutting. To prevent damage to cables, all sharp-edged feed-throughs are protected by a rubber membrane grommet. The license plate is made of sheet steel and is 2 mm thick. It is precisely cut to size using a laser. After edging, it is given a weather-resistant black powder coating.This ensures an optimum fit and durability.The stepless adjustment option allows you to position the plate as required without drilling. There is an additional locking screw to hold the plate in this position.The width of the blinker brackets on the HIGHSIDER AKRON-RS can be adjusted and are therefore suitable for all types of accessory indicators. This adjustment option allows you to adapt the position of your indicators to a wide variety of license plates. The 10 mm holes are slotted to the side to allow the indicators to be fitted without disconnecting them from the wiring harness.You can also individually adjust the position of the rear reflector using a slider. This makes it easy to adapt to the different versions of EU license plates.Two rubber washers are included to securely screw the license plate and reduce vibrations. Another rubber buffer supports the license plate on its underside.Details: - Model-specific bracket - Infinitely adjustable blinker holder - Slotted blinker holder for easy installation without cable separation - Infinitely adjustable reflector, E-approved - Suitable for European license plates - Infinitely adjustable tilt angle - Additional screw for optimum positional security - Easy to fix without additional work steps (e.g. drilling) 5 - Includes two rubber washers.E.g. drilling) - simple mounting of the license plate through slotted holesThe scope of delivery of the HIGHSIDER AKRON-RS includes - Model-specific bracket with mounting parts - HIGHSIDER AKRON-RS license plate mounting plate - Adjustable blinker brackets - E-approved reflector with adjustable bracket - Installation instructions Notes: - If side reflectors are fitted to your original license plate holder, these must be refitted in a suitable position or replaced with new ones. - The special 280-978 blinker holder is optionally available for the original indicators. Tips: If you have not found a model-specific license plate holder for your vehicle, you are sure to find one among the universal license plate holders from HIGHSIDER, which are available in many different designs.
HIGHSIDER pro X-Bar Cross Bar X00 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Drag Bar Wide XD2 Handlebar Aluminum Black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Drag Bar XD1 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike Flat XN1 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Black Bead-Shallow, Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Silver Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 handlebars black glossy, aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER smart Type BC 002 Repair Brake Lever Silver With ABE (1pc)
It doesn't always have to be the original. Our HIGHSIDER smart brake levers replace the original 1 to 1. Precisely manufactured from high-quality aluminum, they meet all requirements. Therefore also with ABE. If you are also looking for the right clutch lever, you are sure to find it in our bike finder.
SHAD Tank Click System
Das Click System von SHAD ist die Weiterentwicklung der Befestigungssysteme für Tankrucksäcke. Neben der einfachen Handhabung und der Integration in das Motorrad zeichnet es sich durch den Push Button aus, mit dem sich der Tankrucksack durch einfaches Drücken schnell entriegeln lässt.
SW-Motech Crash pad kit black for Triumph Street Triple models - SW Motech
Additional protection in the event of a fall is provided by frame crash pads. Shape, surface and material provide excellent sliding properties and reduce damage to the motorcycle. The robust aluminum substructure is easy to install and, if necessary, the CNC-milled abrasive pads made of abrasion-resistant polyamide can be quickly replaced. Protection of frame, engine and fairing Shapely grinding pad made of abrasion-resistant polyamide that can be replaced if necessary Large contact surface for best possible force distribution Optimized surface with good sliding properties Extremely solid, CNC-milled substructure made of aluminum alloy Easy mounting and stable frame connection thanks to model-specific mounting elements Suitable for the following vehicles Triumph Street Triple S A2 (660 cc) (17-), HD03 Triumph Street Triple S A2 (660 cc) (17-), HD02 Triumph Street Triple S A2 (660 cc) (18-19), HD02A Triumph Street Triple S A2 (660 cc) (18-19), HD03A Triumph Street Triple S A2 (660 cc) (18-19), HD03A Triumph Street Triple S A2 (660 cc) (19-), HD05 Triumph Street Triple (675 cc) (12-16), L67LR Triumph Street Triple R (675 cc) (12-16), L67LR Triumph Street Triple Rx (675 cc) (15-16), L67LR Triumph Street Triple RS (765 cc) (16-19), HD01A Triumph Street Triple R (765 cc) (16-18), HD01 Triumph Street Triple RS (765 cc) (16-19), HD01 Triumph Street Triple S (765 cc) (16-18), HD01 Triumph Street Triple R (765 cc) (18-19), HD01A Triumph Street Triple S (765 cc) (18-19), HD01A Triumph Street Triple R (765 cc) (19-), HD01 Triumph Street Triple RS (765 cc) (19-), HD04 Triumph Street Triple S (765 cc) (19-), HD01 Triumph Street Triple R (765 cc) (19-), HD04 Details Material: PA6 Ertalon / aluminum Surface: anodized Color: black / silver Total weight: approx. 2,0 kg Scope of delivery 2 x crash pad kit for frame mounting Mounting instructions Mounting material
